Coal combustion processes are the main source of mercury emission to the environment in Poland. Mercury is emitted by both power and heating plants using hard and brown coals as well as in households. With an annual mercury emission in Poland at the level of 10 Mg, the households emit 0.6 Mg. In the paper, studies on the mercury release in the coal and biomass combustion process in household boilers were conducted. The mercury release factors were determined for that purpose. For the analyzed samples the mercury release factors ranged from 98.3 to 99.1% for hard coal and from 99.5% to 99.9% for biomass, respectively. Due to the high values of the determined factors, the amount of mercury released into the environment mainly depends on the mercury content in the combusted fuel. In light of the obtained results, the mercury content in the examined hard coals was 6 times higher than in the biomass (dry basis). Taking the calorific value of fuels into account, the difference in mercury content between coal and biomass decreased, but its content in coal was still 4 times higher. The mercury content determined in that way ranged from 0.7 to 1.7 μg/MJ for hard coal and from 0.1 to 0.5 μg/MJ for biomass, respectively. The main opportunity to decrease the mercury emissions from households is offered by the use of fuels with a mercury content that is as low as possible, as well as by a reduction of fuel consumption. The latter could be obtained by the use of modern boilers as well as by the thermo-modernization of buildings. It is also possible to partially reduce mercury emissions by using dust removal devices.

In the beginnings of COVID-19 pandemic outbreak public opinion has been con-centrated on the tragic events taking place at the cruise ships, where the new virus has spread substantially. It is not the first outbreak of the infectious disease at a cruise ship. The following article aims at presenting the relevant case law of the British courts that have considered carrier’s liability for passengers’ claims in relation to personal injury caused by the outbreak of gastrointestinal illnesses caused by the norovirus. Fur-thermore, the readers will be familiarized with the legal situation of injured passengers under the American law.

The results of pyrolysis of pine chips and refuse derived fuel fractions are presented. The experiments were carried out in a pilot pyrolysis reactor. The feedstock was analyzed by an elemental analyzer and the X-ray fluorescence spectrometer to determine the elemental composition. To find out optimum conditions for pyrolysis and mass loss as a function of temperature the thermogravimetric analysis was applied. Gases from the thermogravimetric analysis were directed to the infrared spectrometer using gas-flow cuvette to online analysis of gas composition. Chemical composition of the produced gas was measured using gas chromatography with a thermal conductivity detector and a flame ionization detector. The product analysis also took into account the mass balance of individual products.

In this paper, the power factor correction system consisted of: bridge converter, parallel resonant circuit, high frequency transformer, diode rectifier and LFCF filter is presented. This system is controlled by a pulse density modulation method and the principle of its operation is based on the boost technique. The modeling approach is illustrated by an example using AC/HF/DC converter. Verification of the derived model is provided, which demonstrated the validity of the proposed approach.

In this paper, a novel bacterial foraging algorithm (BFA) based approach for robust and optimal design of PID controller connected to power system stabilizer (PSS) is proposed for damping low frequency power oscillations of a single machine infinite bus bar (SMIB) power system. This paper attempts to optimize three parameters (Kp, Ki, Kd) of PID-PSS based on foraging behaviour of Escherichia coli bacteria in human intestine. The problem of robustly selecting the parameters of the power system stabilizer is converted to an optimization problem which is solved by a bacterial foraging algorithm with a carefully selected objective function. The eigenvalue analysis and the simulation results obtained for internal and external disturbances for a wide range of operating conditions show the effectiveness and robustness of the proposed BFAPSS. Further, the time domain simulation results when compared with those obtained using conventional PSS and Genetic Algorithm (GA) based PSS show the superiority of the proposed design.

In literature as well as in the university debate, we can observe the increase of interest regarding converting agricultural residues into energy. Furthermore, the energy and climate policies have encouraged the development of biogas plants for energy production. One of the most significant reasons of this escalation is that this technology may be both convenient and beneficial. The produced biogas is not only supposed to cover the energy demand like heat and electricity, the resulting digestate has the prospect of a beneficial fertilizer and can thereby influence the energy management plans. This technology is widely introduced to countries, which have large income from agriculture. Not only does this reduce the use of industrial fertilizers, but also finds use for agricultural residues. One of the countries of this type is Vietnam, which is the fifth largest exporter of rice in the world. Over 55% of greenhouse gas emission in Vietnam comes from agriculture. Using innovative technologies such as biogas, may decrease this value in near future. It may also contribute to more sustainable agriculture by decreasing traditional fields burning after the harvesting period. The goal of this research paper is to estimate the possible production of biogas from rice straw to cover the energy demand of the rice mill. Four possible scenarios have been considered in this paper, the present situation and where electricity, energy or both were covered by biogas from agricultural residues. An attempt was made to answer the question whether the amount of biogas produced from agricultural residues is enough for both: electricity and energy supply, for the rice mill. If not, how much rice straw must be delivered from other sources, from which rice is not delivered to the rice mill. The base of the assumptions during the estimation of various values were statistics from FAO and other organizations, secondary sources and data from the existing rice mill in Hậu Mỹ Bắc B in Mekong delta in Vietnam.

Automatic generation of DEM based on image matching technique is an important part in digital photograrnmetry. DEM has been found widely in practical applications as in the fields of surveying, civil engineering, road design, agriculture, military, etc. For large DEM project, accuracy, efficiency, and economy are the three main factors to be taken into account. Accuracy is the first important factor to be considered. The effect of modeling methods on DEM accuracy have been tested. The characteristics of terrain surface are considered as a difficult and traditional topic in generating of DEM. Terrain surface may be open or covered with different objects. For generation of accurate DEM, objects on terrain surface must be detected and filtered. There are many methods for detecting and filtering objects which have been found on the terrain surface. Some of them are basing on mutual location of measured points along definite profiles (geometric analysis) or on images converted. This article presents formulas for automatically detecting and filtering covered objects on the base of the geometric analysis of measured points mutually located along determined profiles in X and Y-direction.

The compressive strength and water absorption of cement mortars with different water-binder ratio (0.35, 0.45 and 0.55) and fly ash content (0, 10%, 20% and 30%) under water immersion were investigated, and the correlation between them was further analyzed. The internal microstructure and phase composition of mortar was studied by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. The results show that the inside of mortar mixed with fly ash displayed the loose and porous microstructure. Therefore, the incorporation of fly ash reduced the compressive strength of mortar, especially the early strength, and the strength decreased with the increase of fly ash content, and the water absorption of mortar also increased. There was a linear correlation between the compressive strength and water absorption of mortar with the equation: f_c = -3.838β + 62.332, where f_c and β represented the compressive strength and water absorption, respectively. Therefore, when the water absorption of mortar immersed in water was measured, its corresponding compressive strength could be preliminarily inferred through this equation, which was of great significance for detecting and identifying the stability and safety of hydraulic structures.