In the foundry industry, many harmful compounds can be found, which as a result of gradual but long-term exposure to employees bring negative results. One of such compounds is phenol (aromatic organic compound), which its vapours are corrosive to the eyes, the skin, and the respiratory tract. Exposition to this compound also may cause harmful effects on the central nervous system and heart, resulting in dysrhythmia, seizures, and coma. Phenol is a component of many foundry resins, especially used in shell moulds in the form of resincoated sands. In order to identify it, the pyrolysis gas chromatography-mass spectrometry method (Py-GC/MS) was used. The tests were carried out in conditions close to real (shell mould process – temperature 300°C). During the measurement, attention was focused on the appropriate selection of chromatographic analysis conditions in order to best separate the compounds, as it is difficult to separate the phenol and its derivatives. The identification of compounds was based on own standards.
No-bake process refers to the use of chemical binders to bond the moulding sand. Sand is moved to the mould fill station in preparation for
filling of the mould. A mixer is used to blend the sand with the chemical binder and activator. As the sand exits the mixer, the binder
begins the chemical process of hardening. This paper presents the results of decomposition of the moulding sands with modified ureafurfuryl
resin (with the low content of furfuryl alcohol below 25 % and different activators: organic and inorganic) on a quartz matrix,
under semi-industrial conditions. Investigations of the gases emission in the test foundry plant were executed according to the method
extended in the Faculty of Foundry Engineering (AGH University of Science and Technology). Article presents the results of the emitted
chosen aromatic hydrocarbons and loss on ignition compared with the different activators used to harden this resin. On the bases of the
data, it is possible to determine the content of the emitted dangerous substances from the moulding sand according to the content of loss on
ignition.
Emission of gases under high temperature after pouring molten metal into moulds, which contain the organic binder or other additives
(solvents or curing agent), may be an important factor influencing both on the quality of the produced castings, and on the state of
environment. Therefore, a comprehensive study of the emitted gases would allow to determine restrictions on the use of the moulding
sands in foundry technologies, eg. the probability of occurrence of casting defects, and identify the gaseous pollutants emitted to the
environment. The aim of the research presented in this paper was to determine the amount of gases that are released at high temperatures
from moulding sands bonded by biopolymer binder and the quantitative assessment of the emitted pollutants with particular emphasis on
chemical compounds: benzene, toluene, ethylbenzene and xylenes (BTEX). The water-soluble modified potato starch as a sodium
carboxymethyl starch with low (CMS-NaL) or high (CMS-NaH) degree of substitution was a binder in the tested moulding sands.
A tests of gases emission level were conducted per the procedure developed at the Faculty of Foundry Engineering (AGH University of
Science and Technology) involving gas chromatography method (GC). The obtained results of the determination of amount of BTEX
compounds generated during the decomposition process of starch binders showed lower emission of aromatic hydrocarbons in comparison
with binder based on resin Kaltharz U404 with the acidic curing agent commonly used in the foundries.
The article presents research results of physico-chemical and environmental issues for the dust generated during dedusting of the
installation for the processing and preparation of moulding sand with bentonite. Particular attention was paid to the content of heavy
metals and emission of gases from the BTEX group, which is one of the determinants of the moulding sands harmfulness for the
environment. The analysis of heavy metals in the test samples indicate that there is an increase of the content of all metals in the dust
compared to the initial mixture of bentonite. The most significant (almost double) increase observed for zinc is probably related to the
adsorption of this element on the dust surface by contact with the liquid metal. The study showed, that dust contained more than 20% of
the amount of montmorillonite and had a loss on ignition at a similar level. The addition of 1% of dust to the used moulding sand results in
almost 30% increase in the total volume of gases generated in casting processes and nearly 30% increase of the benzene emission.
The paper presents the results of thermoanalytical studies by TG/DTG/DTA, FTIR and GC/MS for the oil sand used in art and precision foundry. On the basis of course of DTG and DTA curves the characteristic temperature points for thermal effects accompanying the thermal decomposition reactions were determined. This results were linked with structural changes occurred in sample. It has been shown that the highest weight loss of the sample at temperatures of about 320°C is associated with destruction of C-H bonds (FTIR). In addition, a large volume of gases and high amounts of compounds from the BTEX group are generated when liquid metal interacts with oil sand. The results show, that compared to other molding sands used in foundry, this material is characterized by the highest gaseous emissions and the highest harmfulness, because benzene emissions per kilogram of oil sand are more than 7 times higher than molding sand with furan and phenolic binders and green sand with bentonite and lustrous carbon carrier.
The furan resin offers advantages such as high intensity, low viscosity, good humidity resistance and is suitable for cast different casting
alloys: steel, cast iron and non-ferrous metal casting. For hardening furan resins are used different hardeners (acid catalysts). The acid
catalysts have significant effects on the properties of the cured binder (e,g. binding strength and thermal stability) [1 - 3]. Investigations of
the gases emission in the test foundry plant were performed according to the original method developed in the Faculty of Foundry
Engineering, AGH UST. The analysis is carried out by the gas chromatography method with the application of the flame-ionising detector
(FID) (TRACE GC Ultra THERMO SCIENTIFIC).
The problem of harmful casting resins has been present in foundries for many years. Manufacturers are introducing new products that contain in their composition environmentally and eco-friendly ingredients. Unfortunately, not all types of technology can be used, sometimes environmental benefits are disproportionate to the quality of castings and their price. In the foundry industry, the most popular binders are based on organic compounds (often carcinogenic) and other harmful substances. Due to strict legal regulations regarding environmental protection, as well as care for the foundry's workers' comfort - their occurrence should be reduce to a minimum. These compounds often behave also depending on the conditions of use (temperature, atmosphere). The application of various methods of thermal analysis and spectroscopic methods allows to verify the mechanism of resin decomposition process in relation to conditions in the form in both inert and oxidizing atmosphere. For analysis the resins from cold-box technology, were used TG–DTG–DSC, Py-GC/MS methods and specified the course of changes occurring in combination of different atmosphere.
A determination of the heating degree of the moulding sand with bentonite on the grounds of simulating investigations with the application of the MAGMA program, constitutes the contents of the paper. To this end the numerical simulation of the temperature distribution in the virtual casting mould was performed. It was assumed that the mould cavity was filled with a moulding sand with bentonite of a moisture content 3,2 % and bentonite content 8 %. A computer simulation can be used for predicting the heating degree of moulding sands with bentonite. Thus, prediction of the active bentonite (montmorillonite) content in individual layers of the overheated moulding sand can be done by means of the simulation. An overheating degree of a moulding sand with bentonite, and thus the bentonite deactivation depends on a temperature of a casting alloy, casting mass, ratio of: masssand : masscasting, moulding sand amount in the mould and contact area: metal – mould (geometry of the casting shape). Generally it can be stated, that the bentonite deactivation degree depends on two main factors: temperature of moulding sand heating and time of its operation.
In many foundries, the requirements placed on castings production have risen mainly over the few years. Further trends in recent years have been the ever increasing level of automation and introduction of new alloys, especially composites. On the other hand, the foundry environment has become increasingly difficult because is used many organic binders. Environmental regulations will be further tightened up. These processes are pursued at national, European and global level. Conformity with emission limits is becoming increasingly difficult. The problem is emission of aromatic hydrocarbons, phenol, odours and other harmful compounds to environment. The main purpose of many companies is reduction of this toxins. The new cold-box systems (based on phenolic resins) try to reduce the emission by introducing into the resin structure silicate modifiers. Research presented of this article evaluate the effectiveness of these methods. The results show comparison of two resins ("without" and "with" silicate modifier) for assessment of emission of harmful aromatic hydrocarbons and phenol.
Suitability of the given binding agent for the moulding sands preparation depends on the one hand on the estimation of technological properties of the sand and the mould made of it and the obtained casting quality and on the other hand on the assessment of this sand influence on the natural and working environment. Out of moulding sands used in the foundry industry, sands with organic binders deserve a special attention. These binders are based on synthetic resins, which ensure obtaining the proper technological properties and sound castings, however, they negatively influence the environment. If in the initial state these resins are not very dangerous for people and for the environment, thus under an influence of high temperatures they generate very harmful products, being the result of their thermal decomposition. Depending on the kind of the applied resin (phenol-formaldehyde, urea, furfuryl, urea–furfuryl, alkyd) under an influence of a temperature such compounds as: furfuryl alcohol, formaldehyde, phenol, BTEX group (benzene, toluene, ethylbenzene, xylene), and also polycyclic aromatic hydrocarbons (PAH) can be formed and released. The aim of the study was the development of the method, selection of analytical methods and the determination of optimal conditions of formation compounds from the BTEX group. An emission of these components constitutes one of the basic criteria of the harmfulness assessment of binders applied for moulding and core sands. Investigations were carried out in the specially designed set up for the thermal decomposition of organic substances in a temperature range: 5000 C – 13000 C at the laboratory scale. The object for testing was alkyd resin applied as a binding material for moulding sands. Within investigations the minimal amount of adsorbent necessary for the adsorption of compounds released during the decomposition of the resin sample of a mass app. 15 mg was selected. Also the minimal amount of solvent needed for the desorption of compounds adsorbed in the column with adsorbent was found. The temperature range, in which the maximal amounts of benzene, toluene, ethylobenzene and xylenes are released from the resin, was defined. The qualitative and quantitative analyses of compounds from the BTEX group were performed by means of the gas chromatography combined with the mass spectrometry (GC/MS).
It was found that the addition of carbon fibers (CFs) does not affect the crosslinking process in the microwave radiation (800 W, 2.45
GHz) of the BioCo2 binder, which is a water solution of poly(acrylic acid) and dextrin (PAA/D). It has influence on BioCo2 thermal
properties. The CFs addition improves the thermostability of a binder and leads to the reduction of gas products quantity generated in the
temperature range of 300-1100°C (TG-DTG, Py-GC/MS). Moreover, it causes the emission of harmful decomposition products such as
benzene, toluene, xylene and styrene to be registered in a higher temperatures (above 700°C). BioCo2 binder without CFs addition is
characterized by the emission of these substances in the lower temperature range. This indicates the positive effect of carbon fibers
presence on the amount of released harmful products.
The selected technological tests (permeability, friability, bending strength, tensile strength) have shown that the moulding sand with the
0.3 parts by weight carbon fibers addition displays the worst properties. The addition of 0.1 parts by weight of CFs is sufficient to obtain a
beneficial effect on the analyzed moulding sands properties. The reduction of harmful substances at the higher temperatures can also be
observed.
The effects of silica additive (Poraver) on selected properties of BioCo3 binder in form of an aqueous poly(sodium acrylate) and dextrin (PAANa/D) binder were determined. Based on the results of the thermoanalytical studies (TG-DTG, FTIR, Py-GC/MS), it was found that the silica additive results in the increase of the thermostability of the BioCo3 binder and its contribution does not affect the increase in the level of emissions of organic destruction products. Compounds from group of aromatic hydrocarbons are only generated in the third set temperature range (420-838°C). The addition of silicate into the moulding sand with BioCo3 causes also the formation of a hydrogen bonds network with its share in the microwave radiation field and they are mainly responsible for maintaining the cross-linked structures in the mineral matrix system. As a consequence, the microwave curing process in the presence of Poraver leads to improved strength properties of the moulding sand (���� �� ). The addition of Poraver's silica to moulding sand did not alter the permeability of the moulding sand samples, and consequently reduced their friability. Microstructure investigations (SEM) of microwave-cured samples have confirmed that heterogeneous sand grains are bonded to one another through a binder film (bridges).
This paper focuses on the thermal behavior of the starch-based binder (Albertine F/1 by Hüttenes-Albertus) used in foundry technology of molding sand. The analysis of the course of decomposition of the starch material under controlled heating in the temperature range of 25-1100°C was conducted. Thermal analysis methods (TG-DTG-DSC), pyrolysis gas chromatography coupled with mass spectrometry (Py-GC/MS) and diffuse reflectance spectroscopy (DRIFT) were used. The application of various methods of thermal analysis and spectroscopic methods allows to verify the binder decomposition process in relation to conditions in the form in both inert and oxidizing atmosphere. It was confirmed that the binder decomposition is a complex multistage process. The identification of CO2 formation at set temperature range indicated the progressive process of decomposition. A qualitative evaluation of pyrolysis products was carried out and the course of structural changes occurring in the presence of oxygen was determined based on thermo-analytical investigations the temperature of the beginning of binder degradation in set condition was determined. It was noticed that, significant intensification of Albertine F/1 sample decomposition with formation of more degradation products took place at temperatures above 550ºC. Aromatic hydrocarbons were identified at 1100ºC.
The paper presents the results of an investigation of the gases emission of moulding sands with an inorganic (geopolymer) binder with a relaxation additive, whose main task is to reduce the final (residual) strength and improves knocking-out properties of moulding sand. The moulding sand without a relaxation additive was the reference point. The research was carried out using in accordance with the procedure developed at the Faculty of Foundry Engineering of AGH - University of Science and Technology, on the patented stand for determining gas emissions. Quantification of BTEX compounds was performed involving gas chromatography method (GC).The study showed that the introduction of relaxation additive has no negative impact on gas emissions - both in terms of the total amount of gases generated, as well as emissions of BTEX compounds. Among the BTEX compounds, only benzene is emitted from the tested moulding sands. Its emission is associated with the introduction a small amount of an organic hardener from the group of esters.