Thermo-optic properties enhancement of the bi-stable temperature threshold sensors based on a partially filled photonic crystal fiber was reported. Previously tested transducers filled with a selected group of pure n-alkanes had in most cases differences between switching ON and OFF states. Therefore, the modification of filling material by using additional crystallization centers in the form of gold nanoparticles was applied to minimize this undesirable effect. The evaluation of the thermodynamic properties of pentadecane and its mixtures with 14 nm spherical Au nanoparticles based on the differential scanning calorimetry measurements was presented. Optical properties analysis of sensors prepared with these mixtures has shown that they are bounded with refractive index changes of the filling material. Particular sensor switches ON before melting process begins and switches OFF before crystallization starts. Admixing next group of n-alkanes with these nanoparticles allows to design six sensors transducers which change ON and OFF states at the same temperature. Thus, the transducers with a wider temperature range for fiber-optic multi-threshold temperature sensor tests will be used.

We propose real time phase measurements in liquid crystals cells using Young's interferometer constructed with a new principle with possibility to control the distance between two point sources. The optical interference optical pattern is detected by a bicell photo-detector in a back Fourier focal plane. A phase modulation controlled by a monopixel liquid crystals’ cell placed in a reference arm of interferometer is observed as a dynamic shift of the fringes’ pattern in spatial domain. Concept of signals’ demodulation in the Fourier focal plane will be described using a new approach to the demodulation signals. In this work we evaluate the demodulation condition of our setup and we present measurements of a dynamic phase response for nematic liquid crystals and antiferroelectric liquid crystals cells.

Spectral characteristics and amplitude tunability of a long period grating with a dual- resonance inside fiber loop mirror are studied in terms of applied stress caused by elongation. Inserting the polarization controller between grating and part of polarization maintaining fiber in the loop structure enables tuning of resonance and interferometric peaks. The maximum sensitivity of demonstrated sensor is of 1.943 dB/mε for the range of 1.1–4.4 mε. Combination of these two optical components allows to measure strain in a wider range comparing with sensors based on standard long period grating.

In the paper, an extended analysis of the polarization properties of a liquid crystal cell with a biconically tapered single-mode telecommunication optical fiber was presented. These properties are a result of a sample geometry and used LC materials. They were analyzed by using two theoretical models based on the matrix decomposition methods, i.e., polar and singular-value one. By measuring Mueller matrices, information about losses, depolarization, dichroism and birefringence was obtained. In the experiment two types of tested samples filled with well-known 6CHBT and E7 liquid crystals were prepared and all optical parameters were shown as the voltage dependence. The tested samples have dichroic properties and for both models calculated PDL is similar and it increases from 2.6 to 6.6 dB for E7 and from 0.4 to 2.7 dB for 6CHBT with voltage changes within the range of 40 – 190 V. Optical losses simultaneously decrease from 30 dB to 27 dB and from 36 dB to 28 dB, respectively. The birefringence properties cannot be directly comparable due to differences between both applied models but voltage fluctuations of these parameters are not significant. These results confirm expected dichroic properties of designed device and complete knowledge about its working principles. Moreover, presented analysis validates usefulness of the singular-value decomposition model applied to dichroic optical fiber elements.

An interferometric structure based on a Dual-Resonance Long-Period Grating (DRLPG) within a Fiber Loop Mirror (FLM) is presented in this paper. Its purpose is to measure the refractive index (RI) of liquid analytes. The grating is the RI sensing probe, while the FLM serves as a band-pass filter. Due to the high extinction ratio of the FLM, amplitude measurements can be obtained, allowing implementation of the differential interrogation method to establish the sensitivity of the device. The use of a polarization controller makes it possible to fine-tune the interferometric peaks with respect to the two notches of the DRLPG. Precisely aligned configuration produces a maximum sensitivity of 3871.5 dB/RIU within the RI range of 1.3333 up to 1.3419 with linear sensor response.

This paper deals with an issue of a rotational motion impact on a construction and presents civil engineering applications of a fiber optic rotational seismograph named Fiber-Optic System for Rotational Events & Phenomena Monitoring. It has been designed for a long- term building monitoring and structural rotations’ recording. It is based on the Sagnac effect which enables to detect one-axis rotational motion in a direct way and without any reference system. It enables to detect a rotation component in the wide range of a signal amplitude from 10-8 rad/s to 10 rad/s, as well as a frequency from DC to 1000 Hz. Data presented in this paper show the behavior of a reinforced concrete frame construction on different floors. Several measurements were carried out by placing the applied sensor on different floor levels of a building. The laboratory and in-situ measurements confirmed that Fiber-Optic System for Rotational Events & Phenomena Monitoring is an accurate and suitable device for applications in civil engineering.

The main objective of this work is to characterize the performance of an interferometric fibre sensor which has been designed in order to register rotational phenomena, both in seismological observatories and engineering constructions. It is based on a well-known Sagnac effect which enables to detect one-axis rotational motions in a direct way and without any reference system. The presented optical fibre sensor – FOSREM allows to measure a component of rotation in a wide range of signal amplitude form 10^–8 rad/s to 10 rad/s, as well as frequency from 0 Hz to the upper frequency from 2.56 Hz to 328.12 Hz. The laboratory investigation of our system indicated that it keeps theoretical sensitivity equal to 2·10^–8 rad/s/Hz1/2 and accuracy no less than 3·1^–8 to 1.6·10^–6 rad/s in the above mentioned frequency band. Moreover, system size that equals 0.36×0.36×0.16 m and opportunity to remotely control the system via Internet by special server make FOSREM a mobile and autonomous device.

There exists a need in a quality and accuracy of a three-dimensional laser metrology operating in numerically controlled automatic machines. For this purpose, one sends three laser beams mutually perpendicular. These three beams of the wavelength λ = 0.6328 μm are generated by the same laser and are directed along three independent, orthogonal, mutually perpendicular, optical paths with a given light polarization plain. Using these beams, constituting the frame of coordinates, three independent laser rangefinders are able to determine spatial coordinates of a working tool or a workpiece. To form these optical pulses, a special refractive index matched Half-Wave Plate with nematic Liquid Crystal (LCHWP) was applied. The presented half-wave plate is based on a single Twisted Nematic (TN) cell (with the twist angle Φ = π/2) of a rather high cell gap d ~15 μm filled with a newly developed High-Birefringence Nematic Liquid Crystal Mixture (HBLCM) of optical anisotropy as high as Δn ~0.40 at λ = 0.6328 μm, where the Mauguin limit above 5.00 ~ Δnd >> λ/2 = 0.32 is fulfilled.