The objective of this work is to present an energy analysis of different absorption refrigerating systems operating with diverse refrigerants. Also is applied the method of experimental design to optimize configurations proposed by the absorption pairs used and the operating conditions. Both acceptable coefficient of performance and low operating generator temperature are scrutinised. Therefore, a computer program is developed. An investigation of the thermodynamic properties is presented. Results show the coefficient of performance evolution versus respectively the evaporator temperature, temperature of condensation and generator temperature. A particular interest is devoted to the intermediate pressure effect on the performance of different systems. In order to better converge in the selection of the configuration and the refrigerant, which can ensure a high coefficient of performance associated to relatively low operating generator temperature the plan of experiments has been developed, taking in account all parameters influencing the system performance and the function of operating temperature. Results show that the refrigerating machine containing a compressor between the evaporator and the absorber has a coefficient of performance quite acceptable and that it can work at low generator temperature for about 60 ◦C and using the NH3/LiNO3 as refrigerant.

The presented article describes the method for determining one of the trace elements occurring in coalbismuth. The subjects of the analysis were coal type 34, 35 and their fly ashes derived from Jastrzębska Spółka Węglowa. The main reason for the research was the extensive use of bismuth in many industry sectors. Additionally, bismuth is on the list of deficit elements, therefore the possibility of obtaining an alternative for its recycling source of it is needed, is required. The research was carried out using atomic absorption spectrometry with electrothermal atomization in a graphite cuvette. The samples were incinerated at 800°C and microwave mineralization in a high-pressure closed system was performed until the spectrometric analysis was achieved. In order to achieve mineralization, a mixture of HF and HNO3 acids was used to turn the samples into acidic solutions. The preparation of the samples was based on available literature data and own observations. In the experiment, the effects of the additive modifier was modified by changing the temperature in further steps: drying, incineration, cooling, atomization and burning were described. In addition, the palladium modifier was used in order to limit secondary reactions and enable the evaporation of matrix components. The measurement conditions which are presented in this article allow for a linear calibration curve to be established. However, this is not clear and the definitive method for determining the bismuth in coal is carried out through the use of ET-AAS.

Twenty-eight two-, three-, four-, and five-component amine mixtures have been evaluated as possible activators of CO2 absorption into aqueous carbonate/bicarbonate solutions. Measurements were per- formed using a pressure autoclave with a sparger at conditions close to industrial ones. On the basis of these results, a formula for a new, more efficient amine activator named INS13 was developed. The activator was tested both in a pilot plant and on an industrial scale in an ammonia plant producing 300 tons/day of ammonia. Activator INS13 was applied in a number of ammonia plants in Poland and abroad.

Number of trace compounds (called biomarkers), which occur in human breath, provide an information about individual feature of the body, as well as on the state of its health. In this paper we present the results of experiments about detection of certain biomarkers using laser absorption spectroscopy methods of high sensitivity. For NO, OCS, C₂H₆, NH₃, CH₄, CO and CO(CH₃)₂ an analysis of the absorption spectra was performed. The influence of interferents contained in exhaled air was considered. Optimal wavelengths of the detection were found and the solutions of the sensors, as well as the obtained results were presented. For majority of the compounds mentioned above the detection limits applicable for medicine were achieved. The experiments showed that the selected optoelectronic techniques can be applied for screening devices providing early diseases detection.

In this study, the magnetic properties and wave absorption characteristics of high entropy alloys are investigated. The high entropy alloys with FeNiMnCoCu, FeNiMnZnCo, and FeNiZnCoCu compositions were synthesized by the sol-gel method. After the sol-gel process, the annealing process and hydrogen reduction process was performed. FeNiMnCoCu and FeNiZnCoCu were revealed soft magnetic property. The saturation magnetization was 12 emu/g and 36 emu/g, respectively. And The coercive force was –45 Oe and –34 Oe, respectively. The high entropy alloy with these compositions was revealed wave absorption property at above 10 gigahertz frequency region. And it has shown the trend that wave absorption frequency has decreased with the sample thickness increasing.

The theoretical estimation of sound absorption coefficient of a surface may give very different results. This will depend on the type of sound field assumed in the theoretical model used for the estimation of its sound absorption coefficient. Absorption coefficients for normal and diffuse sound fields are widely known, although they may be far from the absorption values given by an absorbing material when it is finally installed inside a room or enclosed space, where a sound field closer to a spherical wavefront is more likely to be found. This work presents a theoretical study, which is addressed at obtaining a mathematical expression to calculate the sound absorption coefficient for a variable range of incidence angles, called αs. The presented method uses a circular sound field incidence as an approximation to a spherical incidence. The estimation of this coefficient αs is based on obtaining the incident and reflected sound fields for a surface located facing a lineal source. The advantage of this calculation method over others lies on its capability to give results for circular, normal and random wave incidence depending on the range of incidence angles considered in the calculation.

The compressive strength and water absorption of cement mortars with different water-binder ratio (0.35, 0.45 and 0.55) and fly ash content (0, 10%, 20% and 30%) under water immersion were investigated, and the correlation between them was further analyzed. The internal microstructure and phase composition of mortar was studied by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. The results show that the inside of mortar mixed with fly ash displayed the loose and porous microstructure. Therefore, the incorporation of fly ash reduced the compressive strength of mortar, especially the early strength, and the strength decreased with the increase of fly ash content, and the water absorption of mortar also increased. There was a linear correlation between the compressive strength and water absorption of mortar with the equation: f_c = -3.838β + 62.332, where f_c and β represented the compressive strength and water absorption, respectively. Therefore, when the water absorption of mortar immersed in water was measured, its corresponding compressive strength could be preliminarily inferred through this equation, which was of great significance for detecting and identifying the stability and safety of hydraulic structures.

The paper presents a dual-band plasmonic solar cell. The proposed unit structure gathers two layers, each layer consists of a silver nanoparticle deposited on a GaAs substrate and covered with an ITO layer, It reveals two discrete absorption bands in the infra-red part of the solar spectrum. Nanoparticle structures have been used for light-trapping to increase the absorption of plasmonic solar cells. By proper engineering of these structures, resonance frequencies and absorption coefficients can be controlled as it will be elucidated. The simulation results are achieved using CST Microwave Studio through the finite element method. The results indicate that this proposed dual-band plasmonic solar cell exhibits an absorption bandwidth, defined as the full width at half maximum, reaches 71 nm. Moreover, It can be noticed that by controlling the nanoparticle height above the GaAs substrate, the absorption peak can be increased to reach 0.77.

Dye-sensitized solar cells (DSSCs) were prepared using various food dyes. Food dyes are economically superior to organometallic dyes since they are nontoxic and inexpensive. The spectrophotometric evaluation of chosen food dyes in solution and on a TiO₂ substrate show that the dyes form J-aggregation on the photoelectrode substrate. Oxidation of potential measurements for used food dyes ensured an energetically permissible and thermodynamically favorable charge transfer throughout the continuous cycle of a photo-electric conversion. The performance of dye-sensitized solar cells based on food dyes was studied. The results illustrate that the dye containing carboxylic acid and sulfonic acid as the acceptor group gave the maximum conversion efficiency 4.20%.

This paper is an analysis of determination possibility of the optical absorption coefficient spectra of thin semiconductor layers from their normalized photoacoustic amplitude spectra. Influence of multiple reflections of light in thin layers on their photoacoustic and optical absorption coefficient spectra is presented and discussed in detail. Practical formulae for the optical absorption coefficient spectrum as a function of the normalized photoacoustic amplitude spectrum are derived and presented. Next, they were applied for computations of the optical absorption coefficient spectra of thin In₂S₃ thin layers deposited on a glass substrate. This method was experimentally verified with the optical transmission method.

Structural and optical properties of graphene with a vacancy and B, N, O and F doped graphene have been investigated computationally using density functional theory (DFT). We find that B is a p-type while N, O and F doped graphene layers, as well as graphene with a vacancy are n-type semiconductors. Optical properties for both cases of in plane (E ⊥ c) and out of plane (E || c) polarization of light are investigated. It is observed that with the increase in the number of electrons entering the supercell, the amount of absorption of the system decreases and the absorption peaks are transferred to higher energies (blue shift).