Introduction: Arthrocentesis has been used in the temporomandibular joint (TMJ) to analyze components of the synovial fluid or as a therapeutic procedure associated or not with the admini- stration of a drug. The rabbit is one of the most commonly used animal species as a model for pathologies that affect the TMJ. The aim of this study was to propose a specific technique to perform arthrocentesis on the rabbit TMJ, emphasizing descriptions of reference points and measurements for a successful puncture without complications. Materials and methods: Fourteen adult rabbits (Oryctolagus cuniculus) were used. The project was approved by the Scientific Ethics Committee of the Universidad de La Frontera (File Nº083/2016). Results: The description of the technique was divided into three steps: 1) Location of the rabbit TMJ, 2) Positioning of the needles in the TMJ, and 3) Passage of fluid through the TMJ. Conclusions: This arthrocen- tesis technique could help to simplify the procedure and give the investigator a guide for joint washing and extraction of synovial fluid in the rabbit TMJ.
A “rock bridge”, defined as the closest distance between two joints in a rock mass, is an important feature affecting the jointed rock mass strength. Artificial jointed rock specimens with two parallel joint fractures were tested under uniaxial compression and numerical simulations were carried out to study the effects of the inclination of the rock bridge, the dip angle of the joint, rock bridge length, and the length of joints on the strength of the jointed rock mass. Research results show: (1) When the length of the joint fracture, the length of the rock bridge, and the inclination of the rock bridge stay unchanged, the uniaxial compressive strength of the specimen gradually increases as the inclination of the joint fracture increases from 0° to 90°. (2) When the length of the joint fracture, the length of the rock bridge, and the inclination of the joint fracture stay unchanged, the uniaxial compressive strength of the specimen shows variations in trends with the inclination of the rock bridge increasing from 30° to 150° (3). In the case when the joint is angled from the vertical loading direction, when the dip angle of the joint fracture, the inclination of the rock bridge, and the length of the rock bridge stay unchanged, the uniaxial compressive strength of the specimen gradually decreases with an increasing length of joint fracture. When the dip angle of the joint fracture, the inclination of the rock bridge, and the length of the joint fracture stay unchanged, the uniaxial compressive strength of the specimen does not show a clear trend with an increase of the length of the rock bridge.
Introduction: Temporomandibular disorders (TMD) are the second most common cause of chronic pain in the human musculoskeletal system. The triad of symptoms of TMD includes: pain within the temporomandibular joint (TMJ), limitation of its mobility and crepitations. The aim of the study was to present the methods of physiotherapy and to assess its effectiveness in patients with hypomobility of temporomandibular joints.
Material and Methods: 44 patients (40.2 ± 10.6 years) were examined for signs of TMD using the Manual Functional Analysis of masticatory system (MFA) questionnaire due to DC/TMD. In the above group, 20 patients showed hypomobility of TMJs and myofascial pain. They underwent a 3-week phy-siotherapy consisting of manual therapy and exercises. In the study group, linear measurements of TMJs mobility and palpation of selected masticatory muscles were performed. Pain was assessed before and after 3 weeks of therapy according to Numerical Rating Scale (NRS). Statistical processing of the data was done with STATISTICA 13 and was conducted considering significance at a p-value <0.05.
Results: Significant improvement in TMJ’s mobility, which increased on average by 6.6 mm (p = 0.0005) and reducing of pain, a decrease of 3 points on average on the NRS Scale (p = 0.00002) were achieved.
Conclusions: The applied physiotherapy algorithm, including manual therapy and exercises of mas-ticatory muscles, is effective in the case of improvement TMJ’s range of motion and reduction of pain in patients with hypomobility of TMJ’s.
About 1600 joint fractures were measured in tillites of the Upper Hecla Hoek Formation on the southern shore of Bellsund. Measurements were collected in 12 areas between the Renardbreen and Tjörndalen. Ray diagrams and contour diagrams of joint fractures, and contour diagrams of joint fractures after rotation to pre-folding position were made for each area. The preliminary analysis of diagrams indicates 2 conjugated joint sets: ca. 60°—120° and 0°—30°. This joint system is probably older than folding and was originated under ENE—WSW to NE—SW stress.
The problem of uniqueness and representativeness of steel frame fire resistance assessment is considered in this paper. The thesis, that the selection of analysis method determines the result in both qualitative and quantitative terms is given scrutiny. It is also shown, that the differences between computed values may be significant. The selection of an appropriate computational model for an analysis of this type seems to be especially important, as the possible overestimation of the fire resistance determined during computation is equivalent to an unjustified optimism of the user with respect to the safety level warranted. In the considerations presented here the critical temperature determined for the whole bearing structure is considered as the measure of sought resistance. The determined temperature is associated with the bearing structure reaching the bearing capacity limit state subject to fire conditions, treated as accidental design situation. Two alternative computational methods have been applied during calculations: the first one – classical, based on 1st order statics and using the buckling length concept for members of the considered frame, and the second one – taking account of 2nd order phenomena via simple amplification of the horizontal loads applied to the frame. Special attention has been paid to the influence exerted on the final fire resistance of the considered structure by the real joint rigidity, decreasing with increasing temperature of the structural members. The obtained results differ not only in the value of determined temperature but also in the indicated location of the weakest frame component, determining its safety.
The correct management of underground works, petroleum and gas reservoirs and geothermal applications relies on the hydromechanical behaviour of rock masses. We describe a laboratory approach to measuring permeability for different types of rock specimens. A laboratory system was designed and set up using rock mechanics equipment (a servo-controlled hydraulic press, a Hoek cell, a pump for injecting water and a scale for measuring the volume of water flow). To verify the validity of the permeability measurements, tests were carried out on a reference porous rock (Corvio sandstone), with results showing good agreement with those published in the literature. Tests were subsequently carried out on artificially fissured granite specimens with different joint patterns, submitted to various confinement stresses up to 20 MPa. Results showed good agreement with traditional Klinkenberg test results. Other tests done with artificially fissured specimens are described for demonstrative purposes.
This paper outlines issues associated with gas-shielded braze welding of CU-ETP copper with austenitic steel X5CrNi18-10 (1.4301) using a consumable electrode. The possibilities for producing joints of this type using innovative low-energy welding methods are discussed. The paper provides an overview of the results of metallographic and mechanical (static shear test, microhardness) tests for braze welded joints made on an automated station using the Cold Metal Transfer (CMT) method. Significant differences in the structure and mechanical properties are indicated, resulting from the joint configuration and the type of shielding gas (argon, helium).
The article concerns modern, flexible adhesive joints, which might be used in timber construction. The article discusses the test results carried out for timber elements joints using polymeric adhesives produced by Sika®. The scope of the tests includes the analysis of strength criteria, tests of polymer adhesion to the timber with a pull-off method, tests of polymer layer shearing between timber elements as well as examination of bending of timber elements joined with polymer. The conclusions indicate the types of these polymers which are recommended for the creation of polymeric joints of timber-polymeric type in timber constructions.
The strength of conveyor belts splices made in mines rarely reaches full belt strength. It consists of a number of factors. The primary is the method of their construction and proper selection of ingredients. The significant impact has also has splice quality covering both keeping proper geometry matched to the belt construction and belts working conditions and adherence to the best practices in the field of technologies of their construction.Difficult conditions in underground mines and pressure on reducing conveyor downtime (avoiding production losses) is reflected by a drop in static and dynamic splices strength. This is confirmed by numerous studies of belt splices strength and fatigue life conducted in the Laboratory of Belt Conveying (LTT) within the framework of research and expert opinions commissioned by belt manufacturers and their users. The consequence of too insufficiently low belt splices strength is their low durability, decreasing reliability and, consequently, higher mining transportation costs. Belt splices are in fact the weakest link in the serial structure which form closed loops of interconnected belt sections working in series of conveyors transporting excavated material in the mine. The article presents the results of simulation analyzes analyses investigating how the increase of belt splices durability may contribute to the reduction of transportation costs in the underground mines.
Significant impact factor and psycho-emotional stress in the etiology of dysfunction indicate the need of the routine approach in the treatment of patients with temporomandibular joint disorders to be changed. The aim of the study was to obtain data, documented test results as to the efficiency of progressive muscle relaxation in the treatment of pain caused by temporomandibular joint disorders, as a supplement to previous methods using occlusal splint and other physical therapies. The study included 100 patients of both sexes, aged from 20 to 35 years who were diagnosed with pain due to temporomandibular joint disorders accompanied with high muscle tension of musticatory muscles which were treatment by relaxation therapy. All patients underwent physical examination, specialized functional examination of the masticatory system in accordance with the Polish version of the study RDC/TMD (The Research Diagnostic Criteria of Temporomandibular Disorders, Axis I — physical assessment, Axis II — assessment of psychosocial status and pain — related disability) and assessment of psycho emotional factor and stress, based on the survey developed for their own purpose. The results of the research were obtained using specialized statistical package “R” i386 3.2.3. The results of examinations aft er relaxation therapy showed a signifi cant reduction in the intensity of myofascial pain in all patients. Progressive muscle relaxation can be successfully used as an supportive therapy treatment of patient with dysfunction.
A lithological profile and measurements of the orientation and spacings of natural discontinuity planes were carried out in the Górka-Mucharz sandstone excavation (Krosno Beds, Outer Carpathians, Poland). In addition, the density of the discontinuities was assessed by measuring their spacings using oriented digital photographs of the quarry walls. An orthophotomap was also used in assessing the orientation and density of fractures with the tools available in QGIS. It was shown that digital image analysis can be used as an alternative to direct field measurements, especially in situations where access to an outcrop is difficult. The distributions of spacings larger than 40 cm, obtained by direct measurements and based on digital images of the quarry, were comparable. As a consequence, both measurement techniques yielded similar values of the quantity of blocks (QB), which differed by less than 2% for the minimum block volume in the range 0.4-1.0 m3 and by 6-7% for larger blocks. On the other hand, measurements of discontinuity spacings that were taken on the basis of an orthophotomap can only serve to estimate the approximate maximum value of this parameter. However, the use of orthophotomaps gives a more explicit spatial pattern of the main vertical joint sets than direct measurements in the quarry.
The analysis results also showed the following: (i) the presence of tectonic disturbances visible at the highest level of the deposit; (ii) higher density of set A fractures with planes deepening in the NE direction and a considerable reduction of the QB parameter, particularly in the peripheral NE and SW parts of the deposit; (iii) differences in the orientation of the discontinuity system between particular beds. The variable density of the discontinuities in the excavation is related to the presence of the faults that limit the Górka-Mucharz deposit.