High business competition demands business players to improve quality. The Six Sigma

with DMAIC phases is a strategy that has proven effective in improving product and service quality. This study aims to find the consistency of DMAIC phases implementation and

analyze the objective value in Six Sigma research. By using a number of trusted article

sources during 2005 until 2019, this research finds that 72% research in manufacturing industry consistently implemented DMAIC roadmap especially in case study research type

for problem-solving, while service industry pointed out the fewer number (60%). The causes

of variations and defective products in the manufacturing industry are largely caused by

a 4M 1E factor, while in service industry are caused by human behavior, and it’s system

poorness. Both manufacturing & service industry emphasized standardization & monitoring to control the process which aimed at enhancing process capability and organization

performance to increase customer satisfaction.

Aluminium is one of the main soil components. Usually it is a part of non-toxic aluminosilicates but in low pH values its mobility is higher and - especially in monomeric form is toxic for plants. Selenium is an essential element necessary for animals and humans. Its compounds have anticancer and anti mutagenic character. However, its high uptake from environment, e.g. with food or water could lead to various diseases including embryonic deformity, decreased hatchling survival and death to aquatic organisms. Soil contamination with aluminium leads to disturbances in plant growth as a result of low calcium and magnesium uptake. High concentrations of selenium lead to its accumulation in plant tissues what is the beginning of selenium fate in food chain. In this work a cultivated layer of soils located near five industry plants in the town of Opole (southern Poland) were investigated. Aluminium and selenium content in soils is an effect of two factors: its natural occurrence in rocks (natural content) and human activity - especially chemicals from agriculture, industrial and transport pollutants. Aluminium was determined in the range of 3440 to 14804 mg/kg d.w. Obtained results of selenium concentration covered the range from 27.1 to 958.1 μg/kg d.w. These results are slightly higher than concentrations noted in natural or non-polluted soils, but still low. These amounts of selenium could have more positive than negative effects. Aluminium and selenium concentrations were discussed concurrently with base soils parameters, such as pH, EC and granulometric fractions composition.

Elaborated shapes of many car components are the reason for which the use of casting techniques to fabricate them is a solution wellfounded

from the economical point of view. Currently applicable regulatory requirements concerning emissions of exhaust fumes force the

carmakers to reduce the overall weight of their products, as this is a basic precondition for reducing fuel consumption. As a result, newly

launched car models contain a continuously increasing share of thin-walled castings made of materials which ensure a satisfactory level of

service properties. At the same time, developing new technological processes allowing to extend the service life of individual components

by means of surface improving becomes more and more important.

This article shows incidents associated with the use of gas as an energy carrier. It presents selected incidents which have occurred in Poland and around the world in recent decades. Based on this, consequences of gas and air mixture explosions were analysed as well. The article presents the main causes of gas incidents which have taken place, as per instances which are similar worldwide. Incidents associated with the use of gas are not frequent, but at the same time very tragic as they often lead to illness or even death. In Poland, in the last twenty years, construction area disasters caused by gas explosions account for only 5% of all which have occurred, but the number of fatalities resulting from these cases is approximately 14%. The number of individuals injured reached 39% of all construction disaster victims. Considering all these facts, it is necessary to undertake wide preventive measures in order to increase safety in the use of gaseous fuels.

The possibility of construction disputes can be reduced, but they cannot be avoided due to the uncertain and risky nature of the building industry. Conflicts between construction parties often have very unfavourable effects, such as cost increases, poor construction quality and time extension in the schedule. Lots of studies have been carried out in order to try and avoid these disagreements. However, there are no common resolution tools or techniques due to the improving conditions and scope of contracted works. Advanced methods and dispute reasons should be fully monitored and updated for the applicable solutions. This paper discusses the current major constructional dispute reasons in Turkey. The questionnaire method was applied within the scope of this study. The questionnaire documents were randomly distributed to 80 contractors to analyse major dispute reasons in Turkey. Analysis of the questionnaire results indicates that the major current dispute causes are poor quality of performed works, delays in progress payments, inefficient site management, poorly written contracts and design mistakes.

The relatively limited application of lean in the food process industries has been attributed to

the unique characteristics of the food sector i.e. short shelf-life, heterogeneous raw materials,

and seasonality. Moreover, barriers such as large and inflexible machinery, long setup time,

and resource complexity, has limited the implementation and impact of lean practices in

process industries in general. Contrary to the expectations in the literature, we bring in this

paper a successful experience of lean implementation in a company of the food-processing

sector. By focusing on two lean tools (VSM and SMED), the company reduced changeover

time by 34%, and increased the production capacity of the main production line by 11%.

This improvement enabled the company to avoid the use of temporary workers by extending

the worktime of its workforce during peak months. Moreover, the reduction of setup time

avoided the use of large lot size in production, which, in turn, reduced the total cycle time

of production and the incidence of quality problems.

An elaborate study executed in the direction of exploring energy saving potential shows that more than 20% of electrical energy used in industry is used for pump systems. Experts calculate that more than 30% of this energy can be saved by improving control and diagnosis for pump systems. Unfortunately, the application ratio of such system is small and consequently a large demand for such technological advanced systems can still be observed in the pump industry. Because of this reason and still growing demand of saving energy in industry, two Universities in Germany and Switzerland together with leading German pump manufacturer decided to join their knowledge and skill to work on the project called "Smart Pump". This paper presents one of the first results of this project, which goal is the development of future control methods and diagnosis systems for intelligent pumps.

The article presents the architectural heritage created as a part of the Central Industrial District in the context of the need for its preservation and protection. Presented are selected topics and problems associated with the current technical condition of both industrial and residential buildings. The analysis contain also the impact of modern conservation doctrines and their ability to preserve works of COP’s architecture with the specific conditions of ownership, poor awareness of users and owners, and a large shortage of historical planning sources.

Mineral fillers are mainly utilized in the production of printing and writing papers (P&W) to improve their optical features and their vulnerability to printing. With the high cost of pulp, the aim of their introduction has been to increase mineral loading in paper and reduce the overall cost of production. For many years the only method of paper formation was acid technology, while the only raw material of choice for filling and coating paper and cardboard was kaolin (in the beginning of the 1970s it was 80% of fillers and 94% of coating grades used in Western Europe, while in the USA – 92% and 96%, respectively). The onset on new methods of acid-free (alkaline) paper forming caused a drastic reduction in the kaolin demand for cost-competitive calcium carbonate: GCC – Ground Calcium Carbonate) and PCC – Precipitated Calcium Carbonate. This also resulted from the progressive self-destruction of machine-made acid papers. In 2013, the share of calcium carbonate in the total production of fillers was 83%, while kaolin accounted for 10%, and talc – 7%. The article presents the parameters of principal mineral fillers for the paper industry and the main reasons why they are suitable for particular kinds of paper. Kaolin, due to the platy nature of its main mineral constituent – kaolinite, is preferred in multiple coating papers. The choice of GCC is beneficial because of its low price and properties (especially whiteness). PCC , due to the possibility of shape and particle size modification serves as filler in uncoated woodfree papers, the key features of which are expected to be lightness and opacity. Size distribution is the main difference between PCC and GCC . The article also presents tendencies observed over the last several years in the paper market in Poland, i.e. in a significant growth in coated paper and board for packaging, as well as the decreasing demand for newspaper, which is a consequence of progressive digitalization.

The article presents the urban layout, which is a best-preserved example of industrial estates in northern Italy. The subject of the research is a public space of the Crespi d’Adda settlement in the Province of Bergamo in Lombardy. Particular attention is paid to green areas occurring there, and their current use. Program of the public areas was very varied. The main role, besides the factory, held the public park, which is an important compositional and ideological. element of the layout. Research task was to show on example of Crespi, the current situation of former settlements in northern Italy, which are for the author reference material for settlements analyzed in Poland.

The paper presents results from social research on the Polish business representatives potentially interested in using the floating buildings. The main purposes of the study were to assess the level of knowledge about floating buildings and diag-nose stimulants and inhibitors of their development in the hotel, catering, and water tourism industry.

Combining the quantitative and the qualitative methodology, research was conducted using an on-line survey (CAWI)and Focused Group Interviews (FGI). Both involved a non-probabilistic, purposive sampling to reach a specific subgroup of the industry: owners or employees of catering, hotel or water tourism companies having or considering having a floating building. The group included both new and long-standing companies using facilities on water or with direct and indirect access to the water.

The study identified stimulating and inhibitory factors broken down into internal (context-independent) and external (context-dependent) conditions. Results show that in Poland floating commercial buildings are a niche topic but also a de-velopable one. Although 71% of the respondents notice difficulties resulting from the insufficient infrastructure and 66.5% of them indicate the lack of legal regulations, they also see the potential of floating buildings: depending on the industry, from 90 to 95% respondents find them “definitely attractive” or “rather attractive”. The most common reason for rejecting floating development is the lack of attractive moorages in the area (43.5% answers).