This paper presents new procedure modeling based on finite element method analysis of wood-framed timber structures. The fasteners linking boards of sheathing with the timber frame both modeled applying shell finite element, with individual material parameters, remain the main objective of this manuscript. Material parameters are obtained from experimental tests and numerical identification. The main objective of the paper is the elaboration of the numerical model with high precision of mapping, and, at the same time, diminishing the number of the unknown simplifying the process of the modeling of timber structures. The new presented method leads to a simplification of analysis of multistory wood-framed multifamily building structures.

The paper presents an analysis of the influence of elevated temperature on thin-walled purlins restrained by sheeting. In the first part of the study the bearing capacity of purlins cooperating with sheeting is examined in normal and elevated temperature based on European Standards. Next, special attention is paid to creating a numerical FEM model of the restrained purlins in Abaqus program taking into account different materials properties with respect to temperature increase.

The standard PN-EN_1993-1-5:_2008 (Eurocode 3) compared with the standard (PN-B-03200:_1990) used previously in Poland, introduces extended rules referring to the computations of the bearing capacity of the plated structural elements including the shear lag effect. The stress distribution in the width flanges is variable. Therefore in the case of the beam with the shear lag effect cannot be calculated by the classic beam theory.

In this article a comparison of the results of the calculations of forces distribution, stresses and displacement according to the rule presented in PN-EN_1993 and results of the numerical computations for_3D model (using finite element method) is presented. The elastic shear lag effects, the elastic shear lag effects including effects of the plate buckling and the elastic-plastic shear lag effects including the local instabilities were analysed. The calculations were performed for beams with a small and a large span and an influence of stiffeners was analysed.

Buckling and postbuckling response of thin-walled composite plates investigated experimentally and determinated analytically and numerically is compared. Real dimension specimens of composite plates weakened by cut-out subjected to uniform compression in laboratory buckling tests have been modelled in the finite element method and examined analytically based on P-w² and P-w³ methods. All results were obtained during the experimental investigations and the numerical FEM analysis of a thin-walled composite plate made of a carbon-epoxy laminate with a symmetrical eight-layer arrangement of [90/-45/45/0]_s. The instrument used for this purpose was a numerical ABAQUS^® program.

The numerical algorithm of thermal phenomena is based on the solution of the heat conduction equations in Petrov-Galerkin’s formula using the finite element method. In the modeling of phase transformation in the solid state, the models based on the diagrams of continuous heating and continuous cooling (CHT and CCT). In the modeling of mechanical phenomena, equations of equilibrium and constitutive relationships were adopted in the rate form. It was assumed that the hardened material is elastic-plastic, and the plasticizing can be characterized by isotropic, kinematic or mixed strengthening. In the model of mechanical phenomena besides thermal, plastic and structural strains, the transformations plasticity was taken into account. Thermo-physical size occurring in the constitutive relationship, such as Young’s modulus and tangential modulus, while yield point depend on temperature and phase composition of the material. The modified Leblond model was used to determine transformation plasticity. This model was supplemented by an algorithm of modified plane strain state, advantageous in application to the modeling of mechanical phenomena in slender objects. The problem of thermoelasticity and plasticity was solved by the FEM. In order to evaluate the quality and usefulness of the presented numerical models, numerical analysis of temperature fields, phase fractions, stresses and strains was performed, i.e. the basic phenomena accompanying surface layer of progressive-hardening with a movable heat source of slender elements made of tool steel for cold work.

The approach to numerical analyses was changed by the introduction of Eurocodes . The EN 1993-1-6 standard allows taking into account imperfections on the shape of a buckling form from a linear elastic bifurcation analysis. The article analyses the first ten forms of imperfection from a linear elastic bifurcation analysis on the reduction of the capacity of a cylindrical shell. Calculations were made using finite element methods.

This article presents the results of a numerical analysis of the road acoustic screen deterioration. Due to the fact that road noise barriers are located in an environment of very high corrosivity, the problem is the rusting of the metal cladding of component panels. The presented case study was, therefore, verified to fulfill the requirements presented in the Eurocode EN 1794-1. Static analysis for wind load and dynamic analysis for the load induced from vehicles was carried out. The analysis presented in the article proved the design errors and their contribution to the formation of severe corrosion, as well as demonstrating the importance of dynamic analysis in the design of acoustic screens.

In general, uniform mixing of particles is desirable in the process of particle handling. However, during the charging of sinter feed and upper ore, size segregation must be induced to prevent heat imbalance, ensure bed permeability, and prevent the loss of fine ore. In this study, upper ore charging was simulated using a discrete element method (DEM) to find the optimal method for controlling particle size segregation, and the segregation characteristics in the upper ore bed were investigated when a deflector plate was applied to the charging machine. The degree of vertical segregation increased when a deflector plate was applied, and it was confirmed that the segregation direction in the upper ore bed can be controlled by adjusting the charging direction of the upper ore by using a deflector plate. In order to apply this method directly to the actual process, further study is needed to understand the influence of the characteristics of the deflector plate such as length and angle.

Deep excavation walls can be analyzed and calculated by using classical methods (currently rarely in use due to their many simplifications) or numerical methods. Among the numerical methods we can distinguish a simplified approach, in which the interaction between soil and a wall structure is modelled by a system of elasto-plastic supports, and the finite-element method (FEM) in which the soil is modelled with mesh of elements. It is a common view that if we want to analyze only wall constructions, the first, simplified method of calculation is sufficient. The second method, FEM, is required if we want to further analyze the stress and strain states in the soil and the influence of the excavation on the surrounding area. However, as it is demonstrated in the paper, important differences may appear in the calculation results of both methods. Thus, the safety design of a deep excavation structure depends very much on the choice of calculating method.

In the paper, the method of a numerical simulation concerning diagonal crack propagation in con-crete beams was presented. Two beams reinforced longitudinally but without shear reinforcement were considered during the Finite Element Method analysis. In particular, a nonlinear method was used to simulate the crack evaluation in the beams. The analysis was performed using the commercial program ANSYS. In the numerical simulation, the limit surface for concrete described by Willam and Warnke was applied to model the failure of concrete. To solve the FEM-system of equations, the Newton-Raphson method was used. As the results of FEM calculations, the trajectories of total stains and numerical images of smeared cracks were obtained for two analyzed beams: the slender beam S5 of leff = 1.8 m and the short beam S3k of leff = 1.1 m. The applied method allowed to generate both flexural vertical cracks and diagonal cracks in the shear regions. Some differences in the evaluation of crack patterns in the beams were observed. The greater number of flexural vertical cracks which penetrated deeper in the beam S5 caused the lower stiffness and the greater deformation in the beam S5 compared to the short beam S3k. Numerical results were compared with the experimental data from the early tests performed by Słowik [3]. The numerical simulation yielded very similar results as the experiments and it confirmed that the character of failure process altered according to the effective length of the member. The proposed numerical procedure was successfully verified and it can be suitable for numerical analyses of diagonal crack propagation in concrete beams.

The aim of the work was modelling of shaft and calculation of natural vibration frequencies and critical rotations of a large-size, vertical mixed flow pump of total length l=4866 mm. Equations of motion were determined analytically, and then calculation results were verified by numerical modelling. The difficulty of the problem consisted in the shaft bearing, in which four hydrodynamic bearings of unknown parameters were applied. A four-mass beam supported on flexible supports of rigidity k and damping c was assumed as the discrete model of the shaft. Equations of motion for the system were derived with the method of forces. In order to verify correctness of the derived equations, one considered three models of the beam with different support configuration: the beam supported on rigid supports, the beam supported on elastic supports, and the beam supported on flexible supports of rigidity k and damping c. Calculation results are presented in tables and graphs.

The paper presents analysis of the vibrational environment on scaffoldings. It is based on the results obtained in the project considering workers safety on scaffoldings. The total number of 120 façade scaffoldings was analysed over a period of two years. One of the issues considered in this project was the vibrations influence on scaffoldings and workers safety. The values of natural frequencies were obtained based on in-situ measurements of free vibrations. Analysis of the tests results made it possible to verify the elaborated numerical models. Values of natural frequencies and displacements in mode shaped from numerical modal analyses were compared with test results. Measurements of forced vibrations were also made with various sources of vibrations active at scaffoldings. The detailed numerical dynamic analysis was performed considering excitation forces variable in time. The obtained results were compared with allowable values according to the appropriate Polish standards. Most influential sources of vibrations for human comfort were indicated in the conclusions.

In the ironmaking, sizes of raw materials such as iron ores and coke must be adjusted for subsequent process in the blast furnace. The depletion of high grade iron ore in recent years necessitates a technology that can utilize low-grade fine iron ores. Thus, steelmakers have been studying the sinter-briquette complex firing process that employs a method of charging the sinter feed together with briquettes made of fine iron ore. In this process, larger briquettes increase the briquette productivity per unit time but decrease the green strength of briquettes and they can break during transportation and charging. Thus, the briquette shape is very important.

Therefore, in this study, we simulate a twin roll briquetting process using the DEM analysis and compared the compressive force distributions in the briquette for different aspect ratios. This study is a new attempt, because research cases by numerical methods on the same or similar systems are very rare. Consequently, the optimal aspect ratio is 0.5 at briquette height 20 mm, 2.0 at 30 mm, and 1.5 at 40 mm. Also, the average compressive force increased in proportion with the pocket height at the same aspect ratio. Therefore, to increase the pocket depth for high productivity, the pocket height must also be increased for obtaining high strength briquettes.

The objective of the paper is to analyse thermodynamical and operational parameters of the supercritical power plant with reference conditions as well as following the introduction of the hybrid system incorporating ORC. In ORC the upper heat source is a stream of hot water from the system of heat recovery having temperature of 90 °C, which is additionally aided by heat from the bleeds of the steam turbine. Thermodynamical analysis of the supercritical plant with and without incorporation of ORC was accomplished using computational flow mechanics numerical codes. Investigated were six working fluids such as propane, isobutane, pentane, ethanol, R236ea and R245fa. In the course of calculations determined were primarily the increase of the unit power and efficiency for the reference case and that with the ORC.

This paper presents and discusses the mathematical model of thermal phenomena occurring in axis-symmetric electromechanical linear motion converters. On the basis of the developed model, software to analyze the process of the heating up of this type of converters, was created. The effect of the thickness and type of material of the slot insulation, as well as the speed of the runner on the temperature distribution in the analyzed object was examined in-depth. Selected results of simulated calculations have been presented.

The main objective of this work was to present a successful stabilization action of a building structure in an active landslide. Firstly, history of the case and a FEM simulation explaining ensuing situation are presented. Then different structural measures to stabilize the whole system are discussed. The structural solution of the problem (pile system reaching solid rocky zone) is presented in more detailed way. The estimation of forces acting on the structure, caused by an unstable soil mass, being crucial for the design of stabilizing structure is described.

Coal waste stockpiles – as artificial formations being a result of the exploitation of underground coal deposits – are constantly influenced by external factors, such as rock mass movements affecting the stability of the stockpile body and changing weather conditions, leading to a cycle of aerological phenomena which intensify the self-heating of the deposited material. Together with the occurrence of external factors, the stored material is also characterised by a set of internal features (also called genetic) that have a direct impact on the kinetics of the self-heating reaction.

The paper focuses mainly on the issue of external factors such as the inclination angle of the stockpile, erosion of the slopes and thermal insulation of the layers of the stored material, which affect the phenomenon of self-heating of the material. Studies of impact of these factors on the thermal stability of coal waste stockpiles are important in the aspect of secondary exploitation of the stockpiles as well as during their reclamation or revitalisation. The numerical solutions presented in the paper should be treated as guidelines that define the directions of analysis for specific cases.