A study was undertaken to investigate the effects of crumb rubber on the strength and mechanical behaviour of Rubberized cement soil (RCS). In the present investigation, 26 groups of soil samples were prepared at five different percentages of crumb rubber content, four different percentages of cement content and two different finenesses of crumb rubber particle. Compressive strength tests were carried out at the curing age of 7 days, 14 days, 28 days and 90 days. The test results indicated that the inclusion of crumb rubber within cement soil leads to a decrease in the compressive strength and stiffness and improves the cement soil’s brittle behaviour to a more ductile one. A reduction of up to 31% in the compressive strength happened in the 20% crumb content group. The compressive strength increases with the increase in the cement content. And the enlargement of cement content is more efficient at low cement content.
The paper presents the results of research on the plastic zones formation in thin (3.51 [mm]) shields made of steel C45 with holes of 4, 10 and 20 diameters. The authorship method of identifying plastic macro-strains utilizing optical interference phenomenon was used in the experiments. The basic idea of the method is summarized below as being: “The occurrence of plastic deformations in the active process of loading is testified by a loss of the interference fringes that were previously present or by a clear and rapid change in their character”. In the experiments, the values of the stress initiating the first plastic deformation were determined. In order to explain the processes of plastic deformation appearance a detailed stress state analysis in the holes surrounding area was realized with the use of Finite Element Method. Comparison of experimental results with the results of FEM calculations indicates that there are significant quantitative as well as qualitative differences. Namely stresses initiating plastic deformations clearly exceed the value of ReH, and plastic deformation are of local plastic slides character. Similar results were previously obtained in studies on the shields made of steel 15CrMo with holes.
Fuzzy logic determination of the material hardening parameters based on the Heyer’s method was applied in this research. As the fuzzy input variables, the length of two measuring bases and the maximum force registered in the Heyer’s test were used. Firstly, the numerical experiment (the simulation of the fuzzification of the input data) with the assumed disturbance of input variables was performed. Next, on the basis of experimental investigations (eleven samples made from the same material), the membership functions associated with the input data were created. After that, the fuzzy analysis was examined. Fuzzy material hardening constants obtained by means of the α-level optimization and the extension principle methods were compared. Discrete values of the hardening data are found in the defuzzification process, by application of the mass center method.
Numerical analysis of the tensioning cables anchorage zone of a bridge superstructure is presented in this paper. It aims to identify why severe concrete cracking occurs during the tensioning process in the vicinity of anchor heads. In order to simulate the tensioning, among others, a so-called local numerical model of a section of the bridge superstructure was created in the Abaqus Finite Element Method (FEM) environment. The model contains all the important elements of the analyzed section of the concrete bridge superstructure, namely concrete, reinforcement and the anchoring system. FEM analyses are performed with the inclusion of both material and geometric nonlinearities. Concrete Damage Plasticity (CDP) constitutive relation from Abaqus is used to describe nonlinear concrete behaviour, which enables analysis of concrete damage and crack propagation. These numerical FEM results are then compared with actual crack patterns, which have been spotted and inventoried at the bridge construction site.
Prof. Małgorzata Kossut of the Nencki Institute of Experimental Biology talks about brain plasticity, the mechanisms of learning, and the mysteries of forgetfulness.
The paper presents research results on the selection of parameters for the asymmetric rolling process of bimetallic plates 10CrMo9-10 + X2CrNiMo17-12-2. They consisted in determining the optimum parameters of the process, which would be ensured to obtain straight bands. Such deformation method introduces in the band the deformations resulting from shear stress, which affect changes in the microstructure. But their effect on the structure is more complicated than in the case of homogeneous materials. It has been shown that the introduction of asymmetric conditions into the rolling process results in greater grain refinement in the so-called hard layer. There was no negative effect on the structural changes in the soft layer observed.
The paper presents the properties of plastics under the trade names of PMMA and Midas, and of Formowax, Romocast 305 and Romocast 930 casting waxes. Their effect on the quality of foundry patterns used in the manufacture of ceramic moulds for precision casting is also discussed. From the selected materials for foundry patterns, samples were made for testing using the following methods: (i) 3D printing in the case of plastics, and (ii) conventional method based on tooling in the form of metal moulds (dies) in the case of casting waxes.
The most important physico-mechanical properties of materials for foundry patterns were determined, i.e. linear shrinkage, softening temperature, relative elongation and coefficient of thermal linear expansion. Bending tests were carried out on samples of patterns printed and made in metal moulds, including determination of the surface roughness of patterns.
After the process of melting out patterns from the cavities of ceramic moulds in an autoclave, the degree of their melting out was visually assessed (i.e. the residues from pattern removal were evaluated). The ash content after burning out of foundry patterns was also determined. The conducted tests allowed comparing the important parameters of materials used for foundry patterns and assessing the suitability of selected plastics as a material for foundry patterns used in the manufacture of high-quality precision castings.
en
pl
