The coal exploitation in the Upper Silesia region (along the Vistula River) triggers the strata seismic
activity, characterized by very high energy, which can create mining damage of the surface objects, without
any noticeable damages in the underground mining structures. It is assumed that the appearance of the
high energy seismic events is the result of faults’ activation in the vicinity of the mining excavation. This
paper presents the analysis of a case study of one coal mine, where during exploitation of the longwall
panel no. 729, the high energy seismic events occurred in the faulty neighborhood. The authors had analyzed
the cause of the presented seismic events, described the methods of energy decreasing and applied
methods of prevention in the selected mining region. The analysis concluded that the cause of the high
energy seismic events, during the exploitation of the longwall panel no. 729 was the rapid displacements
on the fault surface. The fault’s movements arose in the overburden, about 250 m above the excavated
longwall panel, and they were strictly connected to the cracking of the thick sandstone layer.
With reference to the situation experienced in several Polish collieries where the risk of occurrence of gas-geodynamic phenomena is increasing and decisions to start the mining activities need to take numerous constraints associated with previous mining into account, this paper addresses certain geo-mechanical aspects of longwall mining in the zones of excavation edge interactions giving rise to major changes in the conditions of the deposit and rock strata, as a consequence of previous mining operations in adjacent coalbeds. Starting from the analytical description of displacements and stresses in the proximity of longwall mining systems, the paper summarizes the results of model tests and investiga-tions of the influence that the excavation edge has on the behavior and structural continuity of a portion of the coal body in the coalbed beneath or above an old excavation. Based on selected nonlinear functions emulating the presence of edges in the rock strata, a comparative study is carried out by investigating two opposite directions of workface advance, from the gob area towards the coal body and from the coal body towards the gobs. The discussion of the results relies on the analysis of roof deformation and the concentration factor of the vertical stress component at the workface front.
The current rockburst hazard conditions in the copper mines are the consequence of mining-induced seismicity of the rock strata whilst the majority of registered rockbursts have been caused by high-energy seismic events. T he analysis of seismic activity in recent years indicates that the region of the Rudna mine is the region of the highest seismic activity. This paper is an attempt at evaluating the seismicity levels in the Rudna mine in the period from 2006-2015, within the entire mine and in its particular sections. Key parameters of seismic activity include the number of registered seismic events, total energy emission levels, and a unit energy factor. The variability of Gutenberg -Richter (GR) parameters are analyzed and the epicenters’ locations are investigated with respect to the stope position. T he distinction is made between low-energy (103 ≤ As < 105 J) and high-energy (As ≥ 105J) seismic events ahead of the stope, in the opening-up cross-throughs and in the gob areas. It appears that the risk level of a high-energy event occurrence in the R udna mine has not changed in recent years and has remained on a high level whilst the differences in seismic activity, in particular mine sections, are attributed to the varied extraction height and varied thickness of rockburst-prone carbonate layers in the roof of the copper ore deposit. The analysis of the epicenters’ locations with respect to the stope reveals that no matter what the seismic energy levels, the largest number of rockbursts are registered in the opening-up cross-through zone. Low-energy tremors are mostly located in the gob areas, high-energy events occur mostly ahead of the stope. T hus, the evaluation of the seismicity conditions in the Rudna mine seems to positively verify the relationship between the number of registered events and the levels of generated seismic energy, taking the local geological and mining conditions and the specificity of the room and pillar mining method into account.
The application of fluidized fly ash in underground mining excavations is limited due to its significant content of free calcium and calcium sulfate. In order to increase the amount of utilized fly ash from fluidized beds, it should be converted to a product with properties that meet the requirements for mining applications. This research presents the results of an attempt to adapt fluidized fly ashes for use in underground mining techniques, by means of carbonation and granulation. Carbonation was performed with the use of technical carbon dioxide and resulted in the reduction of free calcium content to a value below 1%. Granulation on the other hand, resulted in obtaining a product with good physical and mechanical parameters. The performed mineralogical and chemical studies indicate that trace amounts of “binding” phases, such as basanite and/or gypsum are present in the carbonized ash. The addition of water, during the granulation of carbonized fluidized fly ash, resulted in changes in the mineral phases leading to the formation of ettringite and gypsum as well as the recrystallization of the amorphous substance. It was confirmed that the carbonization and granulation of flying fluidized ashes positively affects the possibility of using these ashes in underground mining excavations.
The article describes mine survey works during opening old St. Anthony of Padua water adit in Horní Město (Czech Republic) to make it accessible to visitors. The works cover the connecting survey and orientation measurement, traverse measurement of the first opened part, setting-out projection of the end of opened part to the surface to make shaft from the surface, new connecting survey and orientation measurement by shaft and traverse measurement of the rest of water adit. Non-standard aids and techniques were used during surveying. One of the tools is a suspended prism holder developed at Institute of geodesy and mine surveying, VSB – Technical university of Ostrava, registered as a utility patent.
The article discusses changes in Polish regulations concerning assessment of the climate hazard in underground mines. Currently, the main empirical index representing the heat strain, used in qualification of the workplace to one of the climate hazard levels in Poland is the equivalent climate temperature. This simple heat index allows easy and quick assessment of the climate hazard. To a major extent, simple heat indices have simplifications and are developed for a specific working environments. Currently, the best methods used in evaluation of microclimate conditions in the workplace are those based on the theory of human thermal balance, where the physiological parameters characterising heat strain are body water loss and internal core temperature of the human body. The article describes the results of research on usage of equivalent climate temperature to heat strain evaluation in underground mining excavations. For this purpose, the numerical model of heat exchange between man and his environment was used, taken from PN-EN ISO 7933:2005. The research discussed in this paper has been carried out considering working conditions and clothing insulation in use in underground mines. The analyses performed in the study allowed formulation of conclusions concerning application of the equivalent climate temperature as a criterion of assessment of climate hazards in underground mines.